WAGNER WideShot Manuel du propriétaire télécharger pdf (Page 4)

English

SELECTING THE PROPER TIP

WIDE ANGLE TIP

The wide angle tip produces a wide pattern that can be adjusted

horizontally or vertically

To adjust:

Make sure the

sprayer is

unplugged.

2. Loosen the wide

angle tip by

turning the tip

counterclockwise

1/4 turn.

3. Turn the

adjusting arm so

that it is pointing down for a horizontal pattern. Turn the

adjusting arm so that it is pointing to the side for a vertical

pattern.

4. Tighten the tip firmly by hand.

ROUND TIP

The round tip produces a round pattern. Use a round tip if the

surface you are spraying is too small for use with the wide angle tip.

The round tip comes in three sizes available at your local

retailer

. Use the size that works best for the type of material

you are spraying. The color of the tip center indicates its size:

Blue (light materials) - .023 inch (0.6mm) opening. This

size works best for oil-based materials.

2. Pink (medium materials) - .031 inch (0.8mm) opening. This

all purpose size works best for oil-based materials.

3. Green (heavy materials) - .039 inch (1.0mm) opening. This

size works best for hard to spray, coarse materials.

STAIN TIP

The stain tip is an option included with some models. It has a

specially designed opening for use with thin materials such as

thin stains, sealers and waterproofers, and can be adjusted to

reduce overspray. If you did not receive a stain tip and will be

spraying one of these materials, the tip can be purchased at

your local retailer.

The stain tip pattern is round with a fine spray. To adjust the

spray pattern size and coarseness, turn the tip slightly

counterclockwise to narrow the pattern and make the spray

more coarse. Turn the tip slightly clockwise to widen the pattern

and make the spray more fine.

IMPORTANT!

Make sure to tighten all spray tips firmly by hand. If the spray

tip is not tightened firmly enough, the sprayer could leak or

the tip could be damaged. Do not use a tool to tighten the

spray tip. If the tip is too tight, it may be damaged.

SETTING THE POWER CONTROL

Your sprayer offers you two

power levels: 100% (II) and

25% (I). The lower the

power level, the closer you

can get to your work and the

less overspray you will have.

Lower power levels give you

greater control but require

more time to cover an area.

To adjust, press the button on the top of the sprayer to to

II for

100% or to I for 25% power.

NOTE:

In order to keep an even spray pattern, you will

need to reduce the amount of material flowing

to the gun as you reduce the power level. Turn

the flow knob clockwise slowly to reduce the

material flow.

Horizontal pattern Vertical pattern

Do not get the power level control wet or the sprayer could

be damaged. Be careful during use and cleanup.

FLOW CONTROL KNOB

The spray pattern is controlled by the flow control knob on the

back of the sprayer, and by the thickness of the material being

sprayed.

Turning the flow knob

counterclockwise increases the amount

of material flow. Turning the flow knob

clockwise decreases

the amount of material flow. To adjust the pattern:

1. Turn the flow knob fully

counterclockwise to maximum.

2. Squeeze the trigger and test the

pattern on a piece of scrap wood

or cardboard.

3. Turn the flow knob

clockwise until

you have a good spray pattern.

• A poor spray pattern will

concentrate the paint in the center

of the spray and go on blotchy.

• A good spray pattern has an even amount of material

throughout the pattern in a fine spray and will go on smoothly.

MATERIAL THINNING

Always test spraying without thinning the material.

Thin as

required to achieve optimum spraying performance (refer to #3,

FLOW CONTROL KNOB).

NOTE: If you are spraying with a material that needs

to be thinned, make sure to follow the

manufacturer

’

s recommendations.

NOTE:

Always practice spraying on a piece of scrap

wood or cardboard to test your spray pattern.

Use the coverage rate recommended by the

material’

s manufacturer

NOTE: If you adjust the flow knob and still cannot get

a good pattern, you may need to thin the

material you are using.

Good spray pattern

Poor spray pattern

INCREASE

CAUTION

NOTE: Always practice spraying on a piece of scrap

wood or cardboard to test your spray pattern.

1 2 3 4 5 6 7 8 9 ... 12 13

Commentaires sur ces manuels

Pas de commentaire

WAGNER WideShot Manuel du propriétaire Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de pulvérisation fine de puissance WAGNER WideShot