Español Français EnglishOwner’s ManualRead this manual for complete instructions0911 • Form No. 0523994CContents 2 Important Safety Information 4
English 10 4. Practice SprayingStartYou will need: • Scrap material / cardboardNotes:If the spray pattern becomes distorted or stops completely whi
English 11 Spray Pattern Overlap Your StrokesSpray Technique50% Overlap8” - 10”(20 - 25 cm)!GOOD SPRAY PATTERN BAD SPRAY PATTERN: TAILINGCORRECTSee p
English 12 Spraying Troubleshooting -Clear the Spray TipStartYou will need: • Scrap material / cardboardDo not attempt to unclog or clean the tip w
English 13 Spraying Troubleshooting -Clean the Spray Gun FilterStartYou will need: • Wrench • Warm, soapy water for latex material • Mineral sp
English 14 Spraying Troubleshooting -Clean the Inlet FilterStartYou will need: • Warm, soapy water for latex material • Mineral spirits for oil b
English 15 Short Term StorageStartEnglishYou will need: • Water • Plastic bag or bucket • Rags • Stir stickThis procedure should be used when
English 16 CleanupStartYou will need: • A water source that can be delivered with a garden hose (latex materials only) • Mineral spirits if using
English 17 5. Remove the inlet lter from the suction tube and place it into waste container. 6. Thread pump cleaning adapter onto garden hose.
English 18 Cleanup - Oil-Based MaterialsStartYou will need: • Mineral spirits if using oil-based material • Warm, soapy water if using latex mate
English 19 Cleaning the Spray Gun ComponentsStartYou will need: • Soft bristled brush • Light household oil • Warm, soapy water if using latex
English 2 SafetySafetyImportant Safety InformationRead all safety information before operating the equipment. Save these instructionsIndicates a haza
English 20 Long Term StorageStartYou will need: • Light household oil / Piston Oil™ • Rags • WrenchIMPORTANT: Store the unit indoors with the
English 21 Cleaning the Sureflo ValveStartYou will need: • Wrenchmay be required if the unit has priming prob
English 22 TroubleshootingBefore servicing, always release system pressure by following Pressure Relief Procedure (page 7).Problem A: The sprayer doe
English 23 Problem E: The spray gun leaksCause Solution1. Gun lter housing is loose Tighten handle2. Internal parts of spray gun are worn or dirty T
English Français Español 7212354Sprayer • Pulvérisateur • Rociador Parts List • Liste de Pièces • Lista de PiezasThis unit contains no electrical ser
EnglishEspañolFrançaisEspañol 734123a5 6 73bSuction set • Dispositif d’aspiration • Juego de succiónParts List • Liste de Pièces • Lista de PiezasIte
English Français Español 74Parts List • Liste de Pièces • Lista de Piezas234167512354GS-07 / GS-08 Spray Gun • Pistolet de GS-07 / GS-08 • Pistola de
EnglishEspañolFrançaisEspañol 75Accessories • Accessoires • AccesoriosPart No. No de piéce Pieza No. English - Description Es
English Français Español 76Limited WarrantyAIRLESS PAINT SPRAY EQUIPMENT This product, manufactured by Wagner Spray Tech (Wagner), is warranted to th
English 3 9. This system is capable of producing 2800 PSI / 193 Bar (9145) or 3000 PSI / 207 Bar (9155/9175/9195). Only use replacement parts or
English 4 What’s in the box?*Start*Certain parts of the sprayer will not be assembled out of the box. Be sure to read Assembly instructions, page 6.
English 5 Proper use and functionsStartControls and FunctionsON/OFF switch:The ON/OFF switch turns power to sprayer on and off. (O=OFF, |=ON)PRIME/SP
English 6 1. AssemblyStart 1. Insert the ends of the hose bracket into the holes of the handle as shown. 2. Remove the plug from inside the hose
English 7 SafetyStartPressure Relief Procedure**Perform when instructedStartImportant Safety WarningBe sure to follow the Pressure Relief Procedure w
English 8 2. Load MaterialStartYou will need: • The material you plan to spray • Flat blade screwdriver (cart models only) • Light household oi
You will need: • Waste bucket • Scrap material / cardboard • Drop cloths to protect oors and furnishings from oversprayNote: Motor will cycle
Commentaires sur ces manuels