Wagner HIGH PERFORMANCE AIRLESS SPRAYER Manuel d'utilisateur

1PRINTED IN THE U. S. A.RForm No. 0270993-11/93505HIGH PERFORMANCEAIRLESS SPRAYERQuestions? ... Need Help?Wagner maintains a toll-free help line for

10SET-UP1. Lock gun. See Figure 4.Figure 4 - Gun in Locked & Unlocked PositionATTACH TIP TO GUN2. If spray tip is not pre- assembled, (See Figure

11SET-UPATTACH RETURN HOSE1. Be sure motor switch is turned OFF.2. Screw brass fitting of return tube into upper port onside of pump. (The brass fitti

12PRIMING1. Lay unit back on its handle so inlet valve is facing up.Fill inlet valve with water or light household oil.2. Make sure Prime/Spray Knob

13Figure 17 - Attaching Paint Pail HandlePRIME THE PUMP1. Attach Suction Tube to inlet valve and tighten firmlyby hand. See Figure 15. Be sure thre

14PRIMING3. TURN SPRAYER ON.4. Turn PRESSURE CONTROL KNOB between halfand full pressure. See Figure 20. You should thenbe able to see the paint mov

15SPRAYINGFigure 24 - Paint Tailing PatternGOOD SPRAY PATTERNPRACTICE FIRST1. Be sure paint hose is free of kinks and clear of trafficor objects with

16SPRAYING1. The key to a good paint job is an even coating over theentire surface. With spray painting, this is done byusing even strokes, with your

175. The spray gun should be triggered off at the end ofeach stroke and on again at the beginning of the next.This avoids paint buildup at the end of

18Figure 32 - Remove And Clean ScreenSPRAYINGContinued from page 17 Cleaning The Spray Gun FilterThe spray gun includes a filter to catch particles be

19SHORT-TERM/OVERNIGHT STORAGEShut-down1. Lock the gun and reduce the pressure. Turn thesprayer to prime A and shut it off. Unplug sprayer.Leave th

2CONTENTSGeneral Description ... 2Safety Precautions ...

20Do not allow paint to build up onthe motor. Overheating of themotor will result. Do not allow flammable solvents tocome in contact with the motor,

2115. Attach paint hose to gun,tighten with two wrenches.CLEAN UP14. Clean spray tip and gun filter with a soft brush.Reassemble spray tip in cleani

22CLEAN UP21. Lock gun, reduce pressure and turn Prime/SprayKnob to prime A .22. Lay unit back on handle so inlet valve is facingupward. Clean thread

23MAINTENANCE4. Thoroughly clean the valve assembly with solventand brush.5. A properly seated valve filled with water and heldvertically will not dri

24MAINTENANCE2. If possible, leave the copper washer under the cap inplace. At least be sure to replace it with the sameside up. (The top will show

25OPTIONAL HOPPER ASSEMBLYCONVERTING SPRAYER FOR HOPPER OPERATIONHopper Return TubeHopperFigure 49 - Optional Hopper4. Screw in the plastic return tub

26Problem Cause RemedySprayer does not start up. Sprayer not plugged in. Plug in.ON/OFF switch OFF. Flip switch to ON.Blown fuse in circuit. Replace f

27Problem Cause RemedySpray gun won't shut off. Worn ball or seat. Take to Authorized Wagner Service Center.Foreign matter or paint Take to Autho

28ITEM PART NO. DESCRIPTION QTY.Parts Diagram – Final Assembly1 0288478 Grip, Handle 12 0270357 Handle, Cart 13 9821503 Washer, Lock 44 9810111 Nut,

29ITEM PART NO. DESCRIPTION QTY. ITEM PART NO. DESCRIPTION QTY.1 0281113 Valve, Inlet Assembly 1(includes item 12)2 0089564 Cap, Outlet Assembly 13 99

3SAFETY PRECAUTIONSThis manual contains information which must be read and understood before using the equipment. When you come to anarea which has on

301239121110ITEM PART NO. DESCRIPTION QTY.ITEM PART NO. DESCRIPTION QTY.7 0270371 Housing, Filter 18 0270369 Filter 19 0090621 Washer 110 0088715 Fitt

31173456AccessoriesPart DescriptionNumber0153000 Hose, 25' x 3/16", Grounded0153001 Hose, 50' x 3/16', Grounded0

32Parts and AccessoriesPARTS LISTItem Part No. Description1 0293004 G-06 Gun Assembly2 0089731 Filter Assembly (Includes Items 3,4,5,6)3 0043590 Spri

33RWagner Spray Tech Corporation1770 Fernbrook LaneMinneapolis, Minnesota 55447Telephone (612) 553-7000 LIMITED WARRANTYAIRLESS PAINT SPRAY EQUI

4WARNINGPREVENTIONHAZARD• Maximum operating range of the gun - 2500 PSI fluidpressure.• NEVER aim the gun at any part of the body.• NEVER allow any p

5Explosion or fire - Solvent and paint fumes can explode orignite, causing property damage and or severe injury.WARNINGHAZARD PREVENTION• Exhaust and

6WARNINGPREVENTIONHAZARDExplosion hazard incompatible materials - May causeproperty damage or severe injury.Hazardous vapors - Paints, solvents, in

7NOTE: More than 100 feet of extension cord is notrecommended. Use more paint hose, not moreextension cord. Shorter extension cords will assuremaxi

8Pressure Relief ProcedureFollow this procedure after the unit is assembled and before any operation which involves the spray gun such aschanging tips

9Pail BracketSET-UPFigure 3B - Attaching Cart HandleBolt, washerand wing nutCart HandleASSEMBLE CART2. Attach cart handle (3). Face the hose hook to